99 lines
3.2 KiB
Arduino
99 lines
3.2 KiB
Arduino
/*
|
|
Configuring port settings using the newer getVal/setVal methods
|
|
By: Nathan Seidle
|
|
SparkFun Electronics
|
|
Date: October 23rd, 2020
|
|
License: MIT. See license file for more information but you can
|
|
basically do whatever you want with this code.
|
|
|
|
This example shows how to query a u-blox module for its UART1 settings and
|
|
then change them if the settings aren't what we want.
|
|
|
|
Note: getVal/setVal/delVal are only support in u-blox protocol versions 27 and higher.
|
|
|
|
Feel like supporting open source hardware?
|
|
Buy a board from SparkFun!
|
|
ZED-F9P RTK2: https://www.sparkfun.com/products/15136
|
|
|
|
Hardware Connections:
|
|
Plug a Qwiic cable into the GNSS and a RedBoard
|
|
If you don't have a platform with a Qwiic connection use the SparkFun Qwiic Breadboard Jumper (https://www.sparkfun.com/products/14425)
|
|
Open the serial monitor at 115200 baud to see the output
|
|
*/
|
|
|
|
#include <Wire.h> //Needed for I2C to GNSS
|
|
|
|
#include "SparkFun_Ublox_Arduino_Library.h" //http://librarymanager/All#SparkFun_u-blox_GNSS
|
|
SFE_UBLOX_GPS myGPS;
|
|
|
|
void setup()
|
|
{
|
|
Serial.begin(115200);
|
|
while (!Serial)
|
|
; //Wait for user to open terminal
|
|
Serial.println("SparkFun u-blox Example");
|
|
|
|
Wire.begin();
|
|
|
|
if (myGPS.begin() == false) //Connect to the u-blox module using Wire port
|
|
{
|
|
Serial.println(F("u-blox GNSS not detected at default I2C address. Please check wiring. Freezing."));
|
|
while (1)
|
|
;
|
|
}
|
|
|
|
bool response = true;
|
|
|
|
//Read the settings from RAM (what the module is running right now, not BBR, Flash, or default)
|
|
uint8_t currentUART1Setting_ubx = myGPS.getVal8(UBLOX_CFG_UART1INPROT_UBX);
|
|
uint8_t currentUART1Setting_nmea = myGPS.getVal8(UBLOX_CFG_UART1INPROT_NMEA);
|
|
uint8_t currentUART1Setting_rtcm3 = myGPS.getVal8(UBLOX_CFG_UART1INPROT_RTCM3X);
|
|
|
|
Serial.print("currentUART1Setting_ubx: ");
|
|
Serial.println(currentUART1Setting_ubx);
|
|
Serial.print("currentUART1Setting_nmea: ");
|
|
Serial.println(currentUART1Setting_nmea);
|
|
Serial.print("currentUART1Setting_rtcm3: ");
|
|
Serial.println(currentUART1Setting_rtcm3);
|
|
|
|
//Check if NMEA and RTCM are enabled for UART1
|
|
if (currentUART1Setting_ubx == 0 || currentUART1Setting_nmea == 0)
|
|
{
|
|
Serial.println("Updating UART1 configuration");
|
|
|
|
//setVal sets the values for RAM, BBR, and Flash automatically so no .saveConfiguration() is needed
|
|
response &= myGPS.setVal8(UBLOX_CFG_UART1INPROT_UBX, 1); //Enable UBX on UART1 Input
|
|
response &= myGPS.setVal8(UBLOX_CFG_UART1INPROT_NMEA, 1); //Enable NMEA on UART1 Input
|
|
response &= myGPS.setVal8(UBLOX_CFG_UART1INPROT_RTCM3X, 0); //Disable RTCM on UART1 Input
|
|
|
|
if (response == false)
|
|
Serial.println("SetVal failed");
|
|
else
|
|
Serial.println("SetVal succeeded");
|
|
}
|
|
else
|
|
Serial.println("No port change needed");
|
|
|
|
//Change speed of UART2
|
|
uint32_t currentUART2Baud = myGPS.getVal32(UBLOX_CFG_UART2_BAUDRATE);
|
|
Serial.print("currentUART2Baud: ");
|
|
Serial.println(currentUART2Baud);
|
|
|
|
if (currentUART2Baud != 57600)
|
|
{
|
|
response &= myGPS.setVal32(UBLOX_CFG_UART2_BAUDRATE, 57600);
|
|
if (response == false)
|
|
Serial.println("SetVal failed");
|
|
else
|
|
Serial.println("SetVal succeeded");
|
|
}
|
|
else
|
|
Serial.println("No baud change needed");
|
|
|
|
Serial.println("Done");
|
|
}
|
|
|
|
void loop()
|
|
{
|
|
}
|