Initial commit - based on v2_candidate

2021-01-09 06:44:12 +00:00
commit 6627841e7d
89 changed files with 31927 additions and 0 deletions
@@ -0,0 +1,94 @@
+/*
+  By: Paul Clark
+  SparkFun Electronics
+  Date: December, 2020
+  License: MIT. See license file for more information but you can
+  basically do whatever you want with this code.
+
+  This example configures the High Navigation Rate on the NEO-M8U and then
+  polls and displays the attitude solution, vehicle dynamics information
+  and high rate position, velocity and time.
+  
+  This example polls the high rate data.
+  (The next example uses "autoHNR" to receive the HNR data automatically.)
+  
+  Please make sure your NEO-M8U is running UDR firmware >= 1.31. Please update using u-center if necessary:
+  https://www.u-blox.com/en/product/neo-m8u-module#tab-documentation-resources
+
+  Feel like supporting open source hardware?
+  Buy a board from SparkFun!
+  NEO-M8U: https://www.sparkfun.com/products/16329
+
+  Hardware Connections:
+  Plug a Qwiic cable into the GPS and a Redboard Qwiic
+  If you don't have a platform with a Qwiic connection use the 
+	SparkFun Qwiic Breadboard Jumper (https://www.sparkfun.com/products/14425)
+  Open the serial monitor at 115200 baud to see the output
+
+*/
+
+#include <Wire.h> //Needed for I2C to GPS
+
+#include <SparkFun_Ublox_Arduino_Library.h> //http://librarymanager/All#SparkFun_u-blox_GNSS
+SFE_UBLOX_GPS myGPS;
+
+void setup()
+{
+  Serial.begin(115200);
+  while (!Serial); //Wait for user to open terminal
+  Serial.println(F("SparkFun u-blox Example"));
+
+  Wire.begin();
+
+  //myGPS.enableDebugging(); // Uncomment this line to enable debug messages on Serial
+
+  if (myGPS.begin() == false) //Connect to the u-blox module using Wire port
+  {
+    Serial.println(F("Warning! u-blox GPS did not begin correctly."));
+    Serial.println(F("(This may be because the I2C port is busy with HNR messages.)"));
+  }
+
+  myGPS.setI2COutput(COM_TYPE_UBX); //Set the I2C port to output UBX only (turn off NMEA noise)
+  myGPS.saveConfigSelective(VAL_CFG_SUBSEC_IOPORT); //Save (only) the communications port settings to flash and BBR
+
+  if (myGPS.setHNRNavigationRate(10) == true) //Set the High Navigation Rate to 10Hz
+    Serial.println(F("setHNRNavigationRate was successful"));
+  else
+    Serial.println(F("setHNRNavigationRate was NOT successful"));
+
+  myGPS.setAutoHNRATT(false); //Make sure auto HNR attitude messages are disabled
+  myGPS.setAutoHNRINS(false); //Make sure auto HNR vehicle dynamics messages are disabled
+  myGPS.setAutoHNRPVT(false); //Make sure auto HNR PVT messages are disabled
+}
+
+void loop()
+{
+  // Poll and print selected HNR data
+  if (myGPS.getHNRAtt(125) == true) // Request HNR Att data using a 125ms timeout
+  {
+    Serial.print(F("Roll: "));
+    Serial.print(myGPS.getHNRroll(), 2); // Use the helper function to get the roll in degrees
+    Serial.print(F(" Pitch: "));
+    Serial.print(myGPS.getHNRpitch(), 2); // Use the helper function to get the pitch in degrees
+    Serial.print(F(" Heading: "));
+    Serial.println(myGPS.getHNRheading(), 2); // Use the helper function to get the heading in degrees
+  }
+  if (myGPS.getHNRDyn(125) == true) // Request HNR Dyn data using a 125ms timeout
+  {
+    Serial.print(F("xAccel: "));
+    Serial.print(myGPS.packetUBXHNRINS->data.xAccel);
+    Serial.print(F(" yAccel: "));
+    Serial.print(myGPS.packetUBXHNRINS->data.yAccel);
+    Serial.print(F(" zAccel: "));
+    Serial.println(myGPS.packetUBXHNRINS->data.zAccel);
+  }
+  if (myGPS.getHNRPVT(125) == true) // Request HNR PVT data using a 125ms timeout
+  {
+    Serial.print(F("ns: "));
+    Serial.print(myGPS.packetUBXHNRPVT->data.nano);
+    Serial.print(F(" Lat: "));
+    Serial.print(myGPS.packetUBXHNRPVT->data.lat);
+    Serial.print(F(" Lon: "));
+    Serial.println(myGPS.packetUBXHNRPVT->data.lon);
+  }
+}